* can't boot plan9 on a stand_alone PC?
@ 1995-08-12 0:12 jmk
0 siblings, 0 replies; 2+ messages in thread
From: jmk @ 1995-08-12 0:12 UTC (permalink / raw)
when you see the 'boot from: ' prompt does it give a list of boot devices
on the previous line? if so, what does it give?
you can copy (under dos) the 9dos file from the floppy to c: then do
c:\plan9\b hd!0!9dos
which will get you up and able to look at the hard discs to see what
went wrong. sounds like the boot partition was overwritten.
------ original message follows ------
>From cse.psu.edu!9fans-outgoing-owner Fri Aug 11 19:00:51 EDT 1995
Received: by colossus.cse.psu.edu id <45581>; Fri, 11 Aug 1995 18:46:13 -0400
Received: from postman.ncube.com ([134.242.8.47]) by colossus.cse.psu.edu with SMTP id <45575>; Fri, 11 Aug 1995 18:45:57 -0400
Received: from db1.ncube.com by postman.ncube.com (4.1/SMI-4.1)
id AA05651; Fri, 11 Aug 95 15:45:31 PDT
Received: from cirque.ncube.com by db1.ncube.com (4.1/SMI-4.1)
id AA16700; Fri, 11 Aug 95 15:45:28 PDT
Date: Fri, 11 Aug 1995 18:45:28 -0400
From: peterw@postman.ncube.com (Peter Wang)
Message-Id: <9508112245.AA16700@db1.ncube.com>
To: 9fans@cse.psu.edu
Subject: can't boot plan9 on a stand_alone PC?
Sender: owner-9fans@cse.psu.edu
Precedence: bulk
Reply-To: 9fans@cse.psu.edu
- The system:
a PC compatiable with a Pentium735 chip, and 853 MB IDE drive.
Made a partition of 80 MB (C drive) and DOS formatted, leaving
the rest of the hard disk to plan9.
- How the problem started:
plan9 runs perfectly until I added additional hard disks and then
did partitions from C:\ using fdisk of DOS command.
- Symptom:
when run plan9 from DOS, c:\plan9\b.com, get error message on screen,
.bad majic 0xf6xxxxxx not a plan 9 executable!
boot from:
- Question:
How to recover?
I would appreciate any hints!
- Peter Wang
^ permalink raw reply [flat|nested] 2+ messages in thread
* can't boot plan9 on a stand_alone PC?
@ 1995-08-11 22:45 Peter
0 siblings, 0 replies; 2+ messages in thread
From: Peter @ 1995-08-11 22:45 UTC (permalink / raw)
- The system:
a PC compatiable with a Pentium735 chip, and 853 MB IDE drive.
Made a partition of 80 MB (C drive) and DOS formatted, leaving
the rest of the hard disk to plan9.
- How the problem started:
plan9 runs perfectly until I added additional hard disks and then
did partitions from C:\ using fdisk of DOS command.
- Symptom:
when run plan9 from DOS, c:\plan9\b.com, get error message on screen,
.bad majic 0xf6xxxxxx not a plan 9 executable!
boot from:
- Question:
How to recover?
I would appreciate any hints!
- Peter Wang
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~1995-08-12 0:12 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
1995-08-12 0:12 can't boot plan9 on a stand_alone PC? jmk
-- strict thread matches above, loose matches on Subject: below --
1995-08-11 22:45 Peter
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).