From mboxrd@z Thu Jan  1 00:00:00 1970
From: jmk@plan9.bell-labs.com
To: 9fans@cse.psu.edu
Subject: Re: [9fans] Ethernet does not start up.
MIME-Version: 1.0
Content-Type: multipart/mixed;
	boundary="upas-hdgqojjmapdsdhdxkcggntyqls"
Message-Id: <20011027163540.B73A2199B9@mail.cse.psu.edu>
Date: Sat, 27 Oct 2001 12:35:38 -0400
Topicbox-Message-UUID: 0f48acec-eaca-11e9-9e20-41e7f4b1d025

This is a multi-part message in MIME format.
--upas-hdgqojjmapdsdhdxkcggntyqls
Content-Disposition: inline
Content-Type: text/plain; charset="US-ASCII"
Content-Transfer-Encoding: 7bit

this is quite commmon, windows puts the hardware into a state
(i think it's to do with power management) whereby it isn't recognised
unless there is a power-off-on in between.

that's the only solution at the moment i'm afraid.

--upas-hdgqojjmapdsdhdxkcggntyqls
Content-Type: message/rfc822
Content-Disposition: inline

Received: from plan9.cs.bell-labs.com ([135.104.9.2]) by plan9; Sat Oct 27 10:36:26 EDT 2001
Received: from mail.cse.psu.edu ([130.203.4.6]) by plan9; Sat Oct 27 10:36:24 EDT 2001
Received: from psuvax1.cse.psu.edu (psuvax1.cse.psu.edu [130.203.18.6])
	by mail.cse.psu.edu (CSE Mail Server) with ESMTP
	id 918AC199ED; Sat, 27 Oct 2001 10:36:11 -0400 (EDT)
Delivered-To: 9fans@cse.psu.edu
Received: from mail508.nifty.com (mail508.nifty.com [202.248.37.216])
	by mail.cse.psu.edu (CSE Mail Server) with ESMTP id 152F4199D5
	for <9fans@cse.psu.edu>; Sat, 27 Oct 2001 10:35:52 -0400 (EDT)
Received: from [192.168.1.31]
	by mail508.nifty.com (8.11.6+3.4W/3.7W-09/06/01) with ESMTP id f9REZmL22919
	for <9fans@cse.psu.edu>; Sat, 27 Oct 2001 23:35:48 +0900
Mime-Version: 1.0
X-Sender: fxba0016@mb.infoweb.ne.jp
X-Mailer: Macintosh Eudora Version 4.3.1-J
Message-Id: <p04310500b80070780dd5@[192.168.1.31]>
To: 9fans@cse.psu.edu
From: Moroo Jun <moroo@nifty.com>
Content-Type: text/plain; charset="us-ascii"
Subject: [9fans] Ethernet does not start up.
Sender: 9fans-admin@cse.psu.edu
Errors-To: 9fans-admin@cse.psu.edu
X-BeenThere: 9fans@cse.psu.edu
X-Mailman-Version: 2.0.6
Precedence: bulk
Reply-To: 9fans@cse.psu.edu
List-Id: Fans of the OS Plan 9 from Bell Labs <9fans.cse.psu.edu>
List-Archive: <http://lists.cse.psu.edu/archives/9fans/>
Date: Sat, 27 Oct 2001 23:35:48 +0900

I'm Plan9 newbee.

I'm trying to install Plan9 on my note pc. But I have troubles.

My note pc can't use Etherlink III except for just power on.
Unfortunately, it can't start rio after rebooting from Windows95.

I used Etherlink III on PCMCIA Slot "1" because Slot 0 connector was broken.
What should I do?

1. After Power on: (Ether is OK, vga is NG)
....
apm ax=f000 cx=f000 dx=40 di=ffff ebx=b66f esi=-1
dev A0 port 1F0 config 0040 capabilities 0F00 mwdma 0407 udma 0007
dev A0 port 170 config 85C0 capabilities 0B00 mwdma 0203
using sdC0!dos!plan9/plan9.ini
#y0: 2 slot Intel 82365SL: port 0x3E0 irq 5
#l0: xcvr10BaseT 3C589
ether#0: 3c589: port 0x110 irq 11: 0060088B00C8
found 9PCDISK .    attr 0x0 start 0x4d len 1441737
....

2. reboot (After using windows95): (Ether is NG, vga is OK)
....
apm ax=f000 cx=f000 dx=40 di=ffff ebx=b66f esi=-1
dev A0 port 1F0 config 0040 capabilities 0F00 mwdma 0407 udma 0007
dev A0 port 170 config 85C0 capabilities 0B00 mwdma 0203
using sdC0!dos!plan9/plan9.ini
#y0: 2 slot Intel 82365SL: port 0x3E0 irq 5
found 9PCDISK .    attr 0x0 start 0x4d len 1441737
....

my plan9.ini is
*nomp=1
distname=plan9
monitor=lcd
vgasize=800x600x8
mouseport=ps2
bootargs=local!#S/sdC0/fs
bootfile=sdC0!9fat!9pcdisk
ether0=type=3c589 port=0x110 irq=11

Best regards,

-- 
Moroo Jun
--upas-hdgqojjmapdsdhdxkcggntyqls--