* [9fans] EDID
2012-10-22 19:22 [9fans] I need some EDID ron minnich
@ 2012-10-23 4:11 ` blstuart
2012-10-23 4:17 ` blstuart
2012-10-23 4:27 ` [9fans] I need some EDID Derek Carter (aka goozbach)
` (3 subsequent siblings)
4 siblings, 1 reply; 10+ messages in thread
From: blstuart @ 2012-10-23 4:11 UTC (permalink / raw)
To: 9fans
> so, if any of you have X11 running, and could do this:
> xrandr --verbose
>From an HP laptop running FreeBSD:
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 1280 x 1280
VGA disconnected (normal left inverted right x axis y axis)
Identifier: 0x41
Timestamp: 81746
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
LVDS connected 1280x800+0+0 (0x44) normal (normal left inverted right x axis y axis) 304mm x 190mm
Identifier: 0x42
Timestamp: 81746
Subpixel: horizontal rgb
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 1
CRTCs: 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff00320c320100000000
00120103801e13780ab3859558538a28
25505400000001010101010101010101
010101010101121b007d502016303020
360030be100000180000000000000000
00000000000000000000000000fe004c
475068696c6970734c43440a000000fe
004c503134315758332d544c4e3200a7
PANEL_FITTING: full_aspect
supported: center full_aspect full
BACKLIGHT_CONTROL: combination
supported: native legacy combination kernel
BACKLIGHT: 0 (0x00000000) range: (0,0)
1280x800 (0x44) 69.3MHz -HSync -VSync *current +preferred
h: width 1280 start 1328 end 1360 total 1405 skew 0 clock 49.3KHz
v: height 800 start 803 end 809 total 822 clock 60.0Hz
1024x768 (0x45) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x46) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x47) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
HDMI-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 81746
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BROADCAST_RGB: 0 (0x00000000) range: (0,1)
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [9fans] EDID
2012-10-23 4:11 ` [9fans] EDID blstuart
@ 2012-10-23 4:17 ` blstuart
2012-10-23 4:33 ` Derek Carter (aka goozbach)
0 siblings, 1 reply; 10+ messages in thread
From: blstuart @ 2012-10-23 4:17 UTC (permalink / raw)
To: 9fans
>> so, if any of you have X11 running, and could do this:
>> xrandr --verbose
>
> From an HP laptop running FreeBSD:
Oops. Sorry about that all.
BLS
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [9fans] EDID
2012-10-23 4:17 ` blstuart
@ 2012-10-23 4:33 ` Derek Carter (aka goozbach)
0 siblings, 0 replies; 10+ messages in thread
From: Derek Carter (aka goozbach) @ 2012-10-23 4:33 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On 10/23/12 0017, blstuart@bellsouth.net wrote:
>>> so, if any of you have X11 running, and could do this: xrandr
>>> --verbose
>>
>> From an HP laptop running FreeBSD:
>
> Oops. Sorry about that all.
>
> BLS
>
>
looks like I did the same thing. Sorry.
- --
Derek
aka goozbach
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2.0.18 (Darwin)
Comment: GPGTools - http://gpgtools.org
Comment: Using GnuPG with Mozilla - http://www.enigmail.net/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=xmsK
-----END PGP SIGNATURE-----
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [9fans] I need some EDID
2012-10-22 19:22 [9fans] I need some EDID ron minnich
2012-10-23 4:11 ` [9fans] EDID blstuart
@ 2012-10-23 4:27 ` Derek Carter (aka goozbach)
2012-10-23 9:41 ` Jean-Pierre Messager
` (2 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Derek Carter (aka goozbach) @ 2012-10-23 4:27 UTC (permalink / raw)
To: 9fans
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On 10/22/12 1522, ron minnich wrote:
> so, if any of you have X11 running, and could do this: xrandr
> --verbose
>
> and send the output to me, subject EDID
>
> I would NOT be forever in your debt, and I will NOT put your name
> in lights, but I would appreciate it :-)
>
> ron
>
Macbook Pro 15" 2012 model
$ xrandr --verbose
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 640 x 480, current 1680 x 1028, maximum 1680 x 1050
default connected 1680x1028+0+0 (0x21d) normal (normal) 0mm x 0mm
Identifier: 0x210
Timestamp: -1982855953
Subpixel: unknown
Clones:
CRTC: 0
CRTCs: 0
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
1680x1050 (0x211) 105.8MHz
h: width 1680 start 0 end 0 total 1680 skew 0 clock
63.0KHz
v: height 1050 start 0 end 0 total 1050 clock
60.0Hz
1680x1050 (0x212) 3.5MHz
h: width 1680 start 0 end 0 total 1680 skew 0 clock
2.1KHz
v: height 1050 start 0 end 0 total 1050 clock
2.0Hz
1440x852 (0x213) 73.6MHz
h: width 1440 start 0 end 0 total 1440 skew 0 clock
51.1KHz
v: height 852 start 0 end 0 total 852 clock
60.0Hz
1280x1024 (0x214) 78.6MHz
h: width 1280 start 0 end 0 total 1280 skew 0 clock
61.4KHz
v: height 1024 start 0 end 0 total 1024 clock
60.0Hz
1152x720 (0x215) 49.8MHz
h: width 1152 start 0 end 0 total 1152 skew 0 clock
43.2KHz
v: height 720 start 0 end 0 total 720 clock
60.0Hz
1024x768 (0x216) 47.2MHz
h: width 1024 start 0 end 0 total 1024 skew 0 clock
46.1KHz
v: height 768 start 0 end 0 total 768 clock
60.0Hz
1024x640 (0x217) 39.3MHz
h: width 1024 start 0 end 0 total 1024 skew 0 clock
38.4KHz
v: height 640 start 0 end 0 total 640 clock
60.0Hz
1280x800 (0x218) 61.4MHz
h: width 1280 start 0 end 0 total 1280 skew 0 clock
48.0KHz
v: height 800 start 0 end 0 total 800 clock
60.0Hz
800x600 (0x219) 28.8MHz
h: width 800 start 0 end 0 total 800 skew 0 clock
36.0KHz
v: height 600 start 0 end 0 total 600 clock
60.0Hz
800x500 (0x21a) 24.0MHz
h: width 800 start 0 end 0 total 800 skew 0 clock
30.0KHz
v: height 500 start 0 end 0 total 500 clock
60.0Hz
640x480 (0x21b) 18.4MHz
h: width 640 start 0 end 0 total 640 skew 0 clock
28.8KHz
v: height 480 start 0 end 0 total 480 clock
60.0Hz
720x480 (0x21c) 20.7MHz
h: width 720 start 0 end 0 total 720 skew 0 clock
28.8KHz
v: height 480 start 0 end 0 total 480 clock
60.0Hz
1680x1028 (0x21d) 1.7MHz *current
h: width 1680 start 0 end 0 total 1680 skew 0 clock
1.0KHz
v: height 1028 start 0 end 0 total 1028 clock
1.0Hz
- --
Derek
aka goozbach
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2.0.18 (Darwin)
Comment: GPGTools - http://gpgtools.org
Comment: Using GnuPG with Mozilla - http://www.enigmail.net/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=qibx
-----END PGP SIGNATURE-----
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [9fans] I need some EDID
2012-10-22 19:22 [9fans] I need some EDID ron minnich
2012-10-23 4:11 ` [9fans] EDID blstuart
2012-10-23 4:27 ` [9fans] I need some EDID Derek Carter (aka goozbach)
@ 2012-10-23 9:41 ` Jean-Pierre Messager
2012-10-23 14:22 ` David Leimbach
2012-10-23 15:50 ` Eugene Gorodinsky
2012-10-23 15:54 ` John Floren
4 siblings, 1 reply; 10+ messages in thread
From: Jean-Pierre Messager @ 2012-10-23 9:41 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
Le 22/10/2012 21:22, ron minnich a écrit :
> so, if any of you have X11 running, and could do this:
> xrandr --verbose
>
> and send the output to me, subject
> EDID
>
> I would NOT be forever in your debt, and I will NOT put your name in
> lights, but I would appreciate it :-)
>
> ron
>
GNU/Linux - Xorg - Monitor: Dell ST2410b
$ xrandr --verbose
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
VGA1 connected 1920x1080+0+0 (0x42) normal (normal left inverted right x
axis y axis) 531mm x 299mm
Identifier: 0x41
Timestamp: 16823
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0010ac5ba055524630
141401030e351e78eeee91a3544c9926
0f5054a54b00714f8180d1c001010101
010101010101023a801871382d40582c
4500132b2100001e000000ff00573138
3952303544304652550a000000fc0044
454c4c205354323431300a20000000fd
00324c1e5311000a20202020202000d9
1920x1080 (0x42) 148.5MHz +HSync +VSync *current +preferred
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock
67.5KHz
v: height 1080 start 1084 end 1089 total 1125 clock 60.0Hz
1280x1024 (0x43) 135.0MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock
80.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 75.0Hz
1280x1024 (0x44) 108.0MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock
64.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.0Hz
1152x864 (0x45) 108.0MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock
67.5KHz
v: height 864 start 865 end 868 total 900 clock 75.0Hz
1024x768 (0x46) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock
60.1KHz
v: height 768 start 769 end 772 total 800 clock 75.1Hz
1024x768 (0x47) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x48) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock
46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x49) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x4a) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock
37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x4b) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock 60.0Hz
720x400 (0x4c) 28.3MHz -HSync +VSync
h: width 720 start 738 end 846 total 900 skew 0 clock
31.5KHz
v: height 400 start 412 end 414 total 449 clock 70.1Hz
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [9fans] I need some EDID
2012-10-23 9:41 ` Jean-Pierre Messager
@ 2012-10-23 14:22 ` David Leimbach
0 siblings, 0 replies; 10+ messages in thread
From: David Leimbach @ 2012-10-23 14:22 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
[-- Attachment #1: Type: text/plain, Size: 1849 bytes --]
Big Damn HP monitor (ZR30w)
Screen 0: minimum 320 x 200, current 2560 x 1600, maximum 8192 x 8192
VGA1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x41
Timestamp: 19460
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDMI1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x42
Timestamp: 19460
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
force_audio: 0 (0x00000000) range: (-1,1)
DP1 connected 2560x1600+0+0 (0x44) normal (normal left inverted right x
axis y axis) 641mm x 400mm
Identifier: 0x43
Timestamp: 19460
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0022f06c2801010101
02160104b5402878e28d85ad4f35b125
0e505400000001010101010101010101
010101010101e26800a0a0402e603020
360081902100001abc1b00a050201730
3020360081902100001a000000fc0048
50205a523330770a20202020000000ff
00434e34323032313338460a2020007b
force_audio: 0 (0x00000000) range: (-1,1)
2560x1600 (0x44) 268.5MHz +HSync -VSync *current +preferred
h: width 2560 start 2608 end 2640 total 2720 skew 0 clock
98.7KHz
v: height 1600 start 1603 end 1609 total 1646 clock
60.0Hz
1280x800 (0x45) 71.0MHz +HSync -VSync
h: width 1280 start 1328 end 1360 total 1440 skew 0 clock
49.3KHz
v: height 800 start 803 end 809 total 823 clock
59.9Hz
[-- Attachment #2: Type: text/html, Size: 5030 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [9fans] I need some EDID
2012-10-22 19:22 [9fans] I need some EDID ron minnich
` (2 preceding siblings ...)
2012-10-23 9:41 ` Jean-Pierre Messager
@ 2012-10-23 15:50 ` Eugene Gorodinsky
2012-10-23 15:54 ` John Floren
4 siblings, 0 replies; 10+ messages in thread
From: Eugene Gorodinsky @ 2012-10-23 15:50 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
[-- Attachment #1: Type: text/plain, Size: 2995 bytes --]
This is a Vaio VGN-CR510E:
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 8192 x 8192
LVDS1 connected 1280x800+0+0 (0x44) normal (normal left inverted right x
axis y axis) 0mm x 0mm
Identifier: 0x41
Timestamp: 11047
Subpixel: horizontal rgb
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 1
CRTCs: 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BACKLIGHT: 8 (0x00000008) range: (0,8)
Backlight: 8 (0x00000008) range: (0,8)
scaling mode: Full aspect
supported: None Full Center Full aspect
1280x800 (0x44) 71.1MHz -HSync -VSync *current +preferred
h: width 1280 start 1292 end 1340 total 1440 skew 0 clock
49.4KHz
v: height 800 start 804 end 807 total 823 clock
60.0Hz
1024x768 (0x45) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock
60.0Hz
800x600 (0x46) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock
60.3Hz
800x600 (0x47) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock
35.2KHz
v: height 600 start 601 end 603 total 625 clock
56.2Hz
640x480 (0x48) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock
59.9Hz
VGA1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x42
Timestamp: 11047
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
TV1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 11047
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
bottom margin: 37 (0x00000025) range: (0,100)
right margin: 46 (0x0000002e) range: (0,100)
top margin: 36 (0x00000024) range: (0,100)
left margin: 54 (0x00000036) range: (0,100)
mode: NTSC-M
supported: NTSC-M NTSC-443 NTSC-J PAL-M
PAL-N PAL 480p@59.94Hz 480p@60Hz
576p 720p@60Hz 720p@59.94Hz 720p@50Hz
1080i@50Hz 1080i@60Hz 1080i@59.94H
2012/10/22 ron minnich <rminnich@gmail.com>
> so, if any of you have X11 running, and could do this:
> xrandr --verbose
>
> and send the output to me, subject
> EDID
>
> I would NOT be forever in your debt, and I will NOT put your name in
> lights, but I would appreciate it :-)
> ron
>
>
[-- Attachment #2: Type: text/html, Size: 7490 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [9fans] I need some EDID
2012-10-22 19:22 [9fans] I need some EDID ron minnich
` (3 preceding siblings ...)
2012-10-23 15:50 ` Eugene Gorodinsky
@ 2012-10-23 15:54 ` John Floren
2012-10-23 18:07 ` ron minnich
4 siblings, 1 reply; 10+ messages in thread
From: John Floren @ 2012-10-23 15:54 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
Everybody, PLEASE, restrain yourselves and send the EDID output to Ron
directly, not to 9fans.
John
On Mon, Oct 22, 2012 at 12:22 PM, ron minnich <rminnich@gmail.com> wrote:
> so, if any of you have X11 running, and could do this:
> xrandr --verbose
>
> and send the output to me, subject
> EDID
>
> I would NOT be forever in your debt, and I will NOT put your name in
> lights, but I would appreciate it :-)
>
> ron
>
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [9fans] I need some EDID
2012-10-23 15:54 ` John Floren
@ 2012-10-23 18:07 ` ron minnich
0 siblings, 0 replies; 10+ messages in thread
From: ron minnich @ 2012-10-23 18:07 UTC (permalink / raw)
To: Fans of the OS Plan 9 from Bell Labs
On Tue, Oct 23, 2012 at 8:54 AM, John Floren <john@jfloren.net> wrote:
> Everybody, PLEASE, restrain yourselves and send the EDID output to Ron
> directly, not to 9fans.
Yes, good point. Also please send with subject
EDID
and you can send the text inline, not as an attachment, thanks
ron
^ permalink raw reply [flat|nested] 10+ messages in thread