Hello

I just need to boot the kenel, this machine is rented, i can't change any hardware configuration, i can just try to get plan9 running there with the help of qemu. . .

I installed  a fossil terminal, now i need to instruct 9load to read the kernel from /dev/sdB0, and if the kernel loads, i need to instruct it to use 9grid.es as the fs and auth.

I will post the results of these tests if they are possitive.

thanks!

gabi

El 22/10/2008, a las 17:47, Sergey Zhilkin escribió:

Hi !

Use 9P instead of iSCSI. In My setup, I use small IDE Flash drives (128Mb) They works just fine ! :)

2008/10/20 <gdiaz@9grid.es>
Hola,

Has anyone done this?

I have access to a cheap hardware which could be a nice plan9 cpu server, the only thing does not work
is the iSCSI disk (or i think so, look at the lspci below)

I suppose the bios of the machine supports booting from iSCSI, so i think i could put a 9load or
9pxeload there,  but 9load is not able to load a kernel from iSCSI and i suppose i can't instruct 9pxeload
to boot from specific server without using bootp/dhcp to boot, right?

any tips on how to make this little thing work? (besides writing iSCSI support for 9load)

here is he lspci output (it is a dualcore atom 1.6ghz intel board, 1gb of ram):


00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev
02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit
Ethernet controller (rev 02)

thanks

gabi
PS: it has an ide controller but with no disks attached






--
С Уважением
Жилкин Сергей