From: "Stefan Hajnoczi" <stefanha@gmail.com>
To: "Fans of the OS Plan 9 from Bell Labs" <9fans@9fans.net>
Subject: Re: [9fans] Eeepc
Date: Thu, 27 Mar 2008 07:52:30 +0000 [thread overview]
Message-ID: <fbd9d3990803270052v2c18afc4n8b7c09a706190ff8@mail.gmail.com> (raw)
In-Reply-To: <13426df10803260821t39f27c93waf220cd5b4b3a1d9@mail.gmail.com>
I just played with an Eee PC for a few minutes. So the Eee PC's
southbridge is not supported by 9load or the kernel. See
/sys/src/boot/pc/pci.c and /sys/src/9/pc/pci.c for the southbridges
list.
I'm not sure how to boot Plan 9 without a CD-ROM drive, so I used dd
to copy the ISO's bootdisk.img onto a USB stick.
I was able to reproduce your error. Then I opened 9load in a hex
editor and changed the 0x8086 0x2640 southbridge entry to 0x8086
0x2641. Here's the result:
PBS1...Plan 9 from Bell Labs
ELCR: 0C28
apm ax=f000 cx=f000 dx=40 di=100 ebx=ef50 esi=ffff
initial probe, to find plan9.ini...dev A0 port 170 config 044A
capabilities 0300 mwdma 0007 udma 101F
pcirouting: 8086/2653 at pin 2 irq 5
pcirouting: 8086/266A at pin 2 irq 5
Boot devices: fd0 sdD0!dos
boot from:
(Note I tried recompiling 9load properly instead of hex editing, but
got hangs and resets)
I have disabled all devices except USB in the BIOS and set "OS
Installation" to "Start".
I am stuck at this point because I have not been able to tell 9load to
boot 9pccd.gz.
Stefan
On Wed, Mar 26, 2008 at 3:21 PM, ron minnich <rminnich@gmail.com> wrote:
> I was not sure what was on there but found
> http://damnsmalllinux.org/cgi-bin/forums/ikonboard.cgi?act=Print;f=8;t=19312
>
> Posted by 9a6or on Nov. 18 2007,05:25
> lspci in DSL gives:
>
> Code Sample
> 0000:00:00.0 Host bridge: Intel Corp.: Unknown device 2590 (rev 04)
> 0000:00:02.0 VGA compatible controller: Intel Corp.: Unknown device
> 2592 (rev 04)
> 0000:00:02.1 Display controller: Intel Corp.: Unknown device 2792 (rev 04)
> 0000:00:1b.0 0403: Intel Corp. I/O Controller Hub Audio (rev 04)
> 0000:00:1c.0 PCI bridge: Intel Corp. I/O Controller Hub PCI Express
> Port 0 (rev 04)
> 0000:00:1c.1 PCI bridge: Intel Corp. I/O Controller Hub PCI Express
> Port 1 (rev 04)
> 0000:00:1c.2 PCI bridge: Intel Corp. I/O Controller Hub PCI Express
> Port 2 (rev 04)
> 0000:00:1d.0 USB Controller: Intel Corp. I/O Controller Hub USB (rev 04)
> 0000:00:1d.1 USB Controller: Intel Corp. I/O Controller Hub USB (rev 04)
> 0000:00:1d.2 USB Controller: Intel Corp. I/O Controller Hub USB (rev 04)
> 0000:00:1d.3 USB Controller: Intel Corp. I/O Controller Hub USB (rev 04)
> 0000:00:1d.7 USB Controller: Intel Corp. I/O Controller Hub USB2 (rev 04)
> 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev d4)
> 0000:00:1f.0 ISA bridge: Intel Corp. I/O Controller Hub LPC (rev 04)
> 0000:00:1f.2 IDE interface: Intel Corp.: Unknown device 2653 (rev 04)
> 0000:00:1f.3 SMBus: Intel Corp. I/O Controller Hub SMBus (rev 04)
> 0000:01:00.0 Ethernet controller: Atheros Communications, Inc.:
> Unknown device 001c (rev 01)
> 0000:03:00.0 Ethernet controller: Unknown device 1969:2048 (rev a0)
>
>
> lspci in Xandros gives:
>
> Quote
>
> 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML
> Express Processor to DRAM Controller (rev 04)
> 00:02.0 VGA compatible controller: Intel Corporation Mobile
> 915GM/GMS/910GML Express Graphics Controller (rev 04)
> 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML
> Express Graphics Controller (rev 04)
> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) High Definition Audio Controller (rev 04)
> 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) PCI Express Port 1 (rev 04)
> 00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) PCI Express Port 2 (rev 04)
> 00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) PCI Express Port 3 (rev 04)
> 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) USB UHCI #1 (rev 04)
> 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) USB UHCI #2 (rev 04)
> 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) USB UHCI #3 (rev 04)
> 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) USB UHCI #4 (rev 04)
> 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
> Family) USB2 EHCI Controller (rev 04)
> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface
> Bridge (rev 04)
> 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA
> Controller (rev 04)
> 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
> SMBus Controller (rev 04)
> 01:00.0 Ethernet controller: Atheros Communications, Inc. AR5007EG
> 802.11 b/g Wireless PCI Express Adapter (rev 01)
> 03:00.0 Ethernet controller: Atheros Technology Corp. L2 100 Mbit
> Ethernet Adapter (rev a0)
>
>
> So, the question is: what about that atheros?
>
> ron
>
>
next prev parent reply other threads:[~2008-03-27 7:52 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-03-24 8:13 Jon Dugan
2008-03-26 7:38 ` sqweek
2008-03-26 15:21 ` ron minnich
2008-03-27 7:52 ` Stefan Hajnoczi [this message]
2008-03-27 9:14 ` Robert Raschke
2008-03-27 9:26 ` Stefan Hajnoczi
2008-03-27 9:51 ` Stefan Hajnoczi
2008-03-27 10:50 ` Gorka Guardiola
2008-03-27 11:03 ` Stefan Hajnoczi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=fbd9d3990803270052v2c18afc4n8b7c09a706190ff8@mail.gmail.com \
--to=stefanha@gmail.com \
--cc=9fans@9fans.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).