Interface language of module documentation

Interface language of module documentation

[Simon Pepping]

Hi,

I am writing a module in which the documentation uses an english
interface. How can I run that documentation through Context? When I
try, dutch control sequences pop up, probably from the modules used
(abr-01 and mod-01), and I get a lot of error messages.

Regards, Simon

-- 
Simon Pepping
email: spepping@scaprea.hobby.nl

Re: Interface language of module documentation

[Hans Hagen]

At 10:27 PM 5/27/2002 +0200, you wrote:
>Hi,
>
>I am writing a module in which the documentation uses an english
>interface. How can I run that documentation through Context? When I
>try, dutch control sequences pop up, probably from the modules used
>(abr-01 and mod-01), and I get a lot of error messages.

--interface=en

Hans

-------------------------------------------------------------------------
                                   Hans Hagen | PRAGMA ADE | pragma@wxs.nl
                       Ridderstraat 27 | 8061 GH Hasselt | The Netherlands
  tel: +31 (0)38 477 53 69 | fax: +31 (0)38 477 53 74 | www.pragma-ade.com
-------------------------------------------------------------------------
                        information: http://www.pragma-ade.com/roadmap.pdf
                     documentation: http://www.pragma-ade.com/showcase.pdf
-------------------------------------------------------------------------

Re: Interface language of module documentation

[Simon Pepping]

On Mon, May 27, 2002 at 10:51:44PM +0200, Hans Hagen wrote:
> At 10:27 PM 5/27/2002 +0200, you wrote:
> >Hi,
> >
> >I am writing a module in which the documentation uses an english
> >interface. How can I run that documentation through Context? When I
> >try, dutch control sequences pop up, probably from the modules used
> >(abr-01 and mod-01), and I get a lot of error messages.
> 
> --interface=en

--interface-en gives this error:

>texexec --pdf --module --interface=en xtag-docbook.tex

 TeXExec 2.5 - ConTeXt / PRAGMA ADE 1997-2001

 TeXUtil 7.3 - ConTeXt / PRAGMA ADE 1992-2000

...snip...

pdftex         : needs map file: original-context-symbol.map
pdftex         : needs map file: pl0-ams-cmr.map
pdftex         : needs map file: original-vogel-symbol.map
! Undefined control sequence.
l.1 \gebruikmodule
                  [abr-01,mod-01]
? 

When I hack texexec to write \usemodule etc. to the texexec.tex
file, I still get complaints about dutch control sequences:

>texexec --pdf --module --interface=en xtag-docbook.tex

 TeXExec 2.5 - ConTeXt / PRAGMA ADE 1997-2001

 TeXUtil 7.3 - ConTeXt / PRAGMA ADE 1992-2000

...snip...

systems        : begin file texexec at line 3
(./xtag-docbook.ted
! Undefined control sequence.
\moduletitel ...\insidefloattrue \steltabulatiein 
                                                  [\c!voor =,\c!na =]\startt...
l.11 ...s Hagen, Simon Pepping, Michael Wiedmann}]

? 

When I do not specify an interface (default = nl) I get this error:

>texexec --pdf --module xtag-docbook.tex

 TeXExec 2.5 - ConTeXt / PRAGMA ADE 1997-2001

 TeXUtil 7.3 - ConTeXt / PRAGMA ADE 1992-2000

...snip...

layout         : achtergronden berekenen
[3.1] . . . [4.2] . .
! Undefined control sequence.
l.150 \subject
              {Analysis of the high level structure of an article}
? 

So there is something about Context's interface language that I do not
do right or that I did not install right.

Simon

-- 
Simon Pepping
email: spepping@scaprea.hobby.nl