From: jnc@mercury.lcs.mit.edu (Noel Chiappa)
To: tuhs@minnie.tuhs.org
Cc: jnc@mercury.lcs.mit.edu
Subject: Re: [TUHS] Fwd: Choice of Unix for 11/03 and 11/23+ Systems
Date: Wed, 23 Sep 2020 21:28:15 -0400 (EDT) [thread overview]
Message-ID: <20200924012815.1FC1E18C099@mercury.lcs.mit.edu> (raw)
> Would also be great if supported RL02 drives. ;)
_Support_ for RL02's will not be a problem (but there are probably some issues
- see below). I have an RL11 driver for V6, which will be easy to include in a
system build. There is also a RL V6 boostrap (which lives in block 0 - it
loads the OS from a V6 filesystem); how to load it off the RL pack on actual
hardware, I'm not sure; do you have some PROM device that has an RL bootstrap
in it?
Or do you have some other drive which is going to be your boot device? If not,
how are you going to get the bits onto an RL pack? This was a bit of an issue
for Fritz Muelller with his -11/45 (with an RK05 drive); he finally wound up
having to load it over a serial line, which took several hours. He used
something called PDP11GUI, and you're in luck, that does support RL02's.
Also, I'm not sure if you've had any experience with an old removable-pack
drive. If not, you have to be very careful with them; if you have a head
crash, the heads are now unobtainium, so a head crash will turn the drive into
junk. (Which is a big part of why Dave Bridgham and I are doing to QSIC RK11
emulator...) The packs need to be absolutely clean; a number of people have
experience with them, you should probably qget some lessons from them before trying
to use it.
> I'd imagine the V6 TTY driver would support boards with multiple serial
> ports. Guess that's what's needed for multi user access.
The TTY code in V6 consists of two levels of driver. The bottom layer is a
driver which is specific to the particular type of card one's using; DL-11,
DZ-11, etc. If the card supports multiple lines, that driver will too. Then
there's a layer above that, tty.c, which the low-level driver uses to interace
to the OS; the user talks to that. That layer is multi-line.
Noel
next reply other threads:[~2020-09-24 1:28 UTC|newest]
Thread overview: 70+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-24 1:28 Noel Chiappa [this message]
-- strict thread matches above, loose matches on Subject: below --
2021-02-03 1:25 Noel Chiappa
2020-10-18 21:36 Norman Wilson
2020-10-12 22:43 Noel Chiappa
2020-10-12 19:27 Noel Chiappa
2020-10-10 23:29 Noel Chiappa
2020-10-11 2:30 ` Jay Logue
2020-10-11 23:24 ` Paul Riley
2020-10-12 0:53 ` Dave Horsfall
2020-10-12 1:56 ` Warner Losh
2020-10-12 2:09 ` Andrew Warkentin
2020-10-12 16:57 ` Arthur Krewat
2020-10-18 20:42 ` Michael Huff
2020-10-08 23:49 Noel Chiappa
2020-10-08 16:06 Noel Chiappa
2020-10-06 23:08 Noel Chiappa
2020-10-07 5:24 ` Jay Logue
2020-10-06 20:34 Noel Chiappa
2020-10-06 19:34 Noel Chiappa
2020-10-06 19:04 Noel Chiappa
2020-10-06 14:46 Noel Chiappa
2020-10-06 16:22 ` jay-tuhs9915
2020-10-02 0:39 Noel Chiappa
2020-10-01 12:51 Noel Chiappa
2020-10-02 0:23 ` Paul Riley
2020-09-30 23:16 Noel Chiappa
2020-09-30 18:51 Noel Chiappa
2020-09-30 17:58 Noel Chiappa
2020-09-28 23:21 Noel Chiappa
2020-09-30 1:50 ` Paul Riley
2020-09-27 21:07 Noel Chiappa
2020-09-27 21:12 ` Warner Losh
2020-09-28 0:22 ` Pete Turnbull
2020-09-27 20:50 Noel Chiappa
2020-09-29 13:20 ` Paul Riley
2020-09-25 22:08 Noel Chiappa
2020-09-26 14:52 ` John Foust
2020-09-28 0:03 ` Paul Riley
2020-09-28 0:06 ` Paul Riley
2020-09-24 18:56 Noel Chiappa
2020-09-24 13:04 Noel Chiappa
2020-09-24 18:24 ` John Cowan
2020-09-24 11:02 Paul Ruizendaal
2021-02-03 0:12 ` Greg A. Woods
2020-09-23 23:14 Noel Chiappa
2020-09-24 1:09 ` John Foust
2020-09-22 21:51 John Foust
2020-09-22 21:36 Noel Chiappa
2020-09-22 21:46 ` Warner Losh
2020-09-22 21:49 ` John Foust
2020-09-22 15:59 Noel Chiappa
2021-02-03 0:07 ` Greg A. Woods
2020-09-22 0:47 Noel Chiappa
2020-09-21 19:37 Noel Chiappa
2020-09-21 23:16 ` devin davison
2020-09-21 18:13 Noel Chiappa
2020-09-21 17:59 Noel Chiappa
2020-09-21 18:18 ` Arthur Krewat
2020-09-20 13:12 Noel Chiappa
2020-09-19 15:28 Noel Chiappa
2020-09-21 10:26 ` Paul Riley
2021-01-24 16:07 ` Tom Ivar Helbekkmo via TUHS
2021-01-25 4:58 ` Gregg Levine
2021-01-25 8:21 ` Tom Ivar Helbekkmo via TUHS
[not found] <CAD05_j1bc6DDRtfPkd4QVeWXjwSp73bty46D=2ATozUbHThBWw@mail.gmail.com>
2020-09-19 3:22 ` Paul Riley
2020-09-19 14:20 ` Heinz Lycklama
2020-09-21 13:54 ` Paul Riley
2020-09-21 15:30 ` Heinz Lycklama
2020-09-21 23:27 ` Henry Bent
[not found] ` <4C35E6D2-8ABD-4DC2-BB2F-F15FA5BF30DD@icloud.com>
2020-09-22 0:22 ` Henry Bent
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200924012815.1FC1E18C099@mercury.lcs.mit.edu \
--to=jnc@mercury.lcs.mit.edu \
--cc=tuhs@minnie.tuhs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).