From: jjsullivan5196 <jjsullivan5196@users.noreply.github.com>
To: ml@inbox.vuxu.org
Subject: Re: [PR PATCH] [Updated] pinephone: add support for modem setup and audio routing.
Date: Fri, 05 Feb 2021 11:17:39 +0100 [thread overview]
Message-ID: <20210205101739.tV861E6kD_7IyDG-8-7j37E3he_x0iRgt1zxLOBzr9c@z> (raw)
In-Reply-To: <gh-mailinglist-notifications-41a7ca26-5023-4802-975b-f1789d68868e-void-packages-25084@inbox.vuxu.org>
[-- Attachment #1: Type: text/plain, Size: 3560 bytes --]
There is an updated pull request by jjsullivan5196 against master on the void-packages repository
https://github.com/jjsullivan5196/void-packages pinephone-qol
https://github.com/void-linux/void-packages/pull/25084
pinephone: add support for modem setup and audio routing.
This pull adds the necessary components for 4G modem usage, with the following use-cases in mind:
- Configure audio setup to and from modem
- Make and receive calls
- Send and read SMS
- Use mobile broadband/cellular data
- Wake-on-Modem (for calls and texts)
For now I've tested this with ModemManager+NetworkManager, but this also provides the groundwork for environments that use `ofono` (or just plain AT commands with `atinout` or `screen`, if you feel clever :^) )
To get started, you first need to run `pinephone-modem-setup` once as root to do the initial modem configuration. (chances are postmarketOS already did this if you booted the phone once, but this might need to be done again incase of potential data loss)
Some use-cases might require further configuration of software (eg specific to NetworkManager) but the setup script should do most of the needed work. Make sure modem is powered up by running `echo 1 > /sys/class/modem-power/modem-power/device/powered_blocking` Some examples of usage that I've tested below:
Read sms with `mmcli`
```sh
$ mmcli -s '/org/freedesktop/ModemManager1/SMS/2'
-----------------------------------
Content | number: '+5555555555'
| text: 'Test'
-----------------------------------
Properties | PDU type: 'deliver'
| state: 'received'
| storage: 'me'
| smsc: '+919810051829'
| timestamp: '160808142935+05'
```
Sample script for answering calls, using ModemManager dbus interface. Audio is setup thru `alsaucm`
```sh
#!/bin/bash
MM_IFACE="org.freedesktop.ModemManager1"
MATCH_CALLS="type='signal',sender='${MM_IFACE}',interface='${MM_IFACE}.Modem.Voice',member='CallAdded'"
do_accept() {
while read TYPE TIME SENDER HEADER
do
if [[ "$HEADER" = *"Modem.Voice"* ]]; then
read TYPE _P OBJ
OBJ=$(echo "${OBJ}" | tr -d '"')
echo "Pickup ${OBJ}"
alsaucm \
open PinePhone \
set _verb 'Voice Call' \
set _enadev 'Mic' \
set _enadev 'Earpiece'
dbus-send \
--system \
--dest="${MM_IFACE}" \
--print-reply \
"${OBJ}" \
"${MM_IFACE}.Call.Accept"
else
read
fi
done
}
dbus-monitor --system "${MATCH_CALLS}" | do_accept
```
Add a NetworkManager connection for LTE (sub `<operator_apn>` for your carrier's data APN)
```sh
$ nmcli c add type gsm ifname '*' con-name LTE apn <operator_apn>
```
For Wake-on-Modem: I tested by doing `loginctl suspend` from a sway session, then calling the phone. It wakes up within 2 rings.
fwiw: these examples are only good for making sure the hardware/software interface works. More work still needs to be done to get some telephony front-end software in the repo, like #24538 Sxmo also should work out-of-the box with the NetworkManager+ModemManager pair https://git.sr.ht/~mil/sxmo-docs
For any concerns about the `COPYING` file, the [original author approves](https://matrix.to/#/!ToPtLQdvveNEbXcHqE:fam-ribbers.com/$YEfAo9NI3WPApA1QbhmQrhwizjmlYXnLkMjby4PU7z4?via=matrix.org&via=feneas.org&via=kde.org).
A patch file from https://github.com/void-linux/void-packages/pull/25084.patch is attached
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: github-pr-pinephone-qol-25084.patch --]
[-- Type: text/x-diff, Size: 13918 bytes --]
From 0d22968acd2e0321afd768099bdc03064ec2a517 Mon Sep 17 00:00:00 2001
From: John Sullivan <jsullivan@csumb.edu>
Date: Fri, 25 Sep 2020 00:44:17 -0700
Subject: [PATCH 1/2] New package: atinout-0.9.1
---
srcpkgs/atinout/template | 14 ++++++++++++++
1 file changed, 14 insertions(+)
create mode 100644 srcpkgs/atinout/template
diff --git a/srcpkgs/atinout/template b/srcpkgs/atinout/template
new file mode 100644
index 00000000000..e292bf9c9c7
--- /dev/null
+++ b/srcpkgs/atinout/template
@@ -0,0 +1,14 @@
+# Template file for 'atinout'
+pkgname=atinout
+version=0.9.1
+revision=1
+build_style=gnu-makefile
+short_desc="Send AT commands to modem and print responses"
+maintainer="John Sullivan <jsullivan@csumb.edu>"
+license="GPL-3.0-or-later"
+homepage="http://atinout.sourceforge.net"
+distfiles="${SOURCEFORGE_SITE}/project/${pkgname}/v${version}/${pkgname}-${version}.tar.gz"
+checksum=4d15c8288aca414e11cd304686b172696104c5e42bf776300311c005634854a2
+
+# Disable -Werror (GCC9+ turns switch fallthrough into error)
+CFLAGS="-W -Wall -Wextra -DVERSION=\\\"${version}\\\" -g"
From 528b2f099d199a148f65b5f93808418c775dd5d7 Mon Sep 17 00:00:00 2001
From: John Sullivan <jsullivan@csumb.edu>
Date: Fri, 25 Sep 2020 01:48:43 -0700
Subject: [PATCH 2/2] pinephone-base: add support for modem setup and audio
routing.
---
.../files/00-alsa-pinephone-dshare.conf | 14 ++
srcpkgs/pinephone-base/files/COPYING | 15 ++
.../files/pinephone-modem-setup | 26 ++++
srcpkgs/pinephone-base/files/ucm/HiFi.conf | 140 +++++++++++++++++
.../pinephone-base/files/ucm/PinePhone.conf | 11 ++
.../pinephone-base/files/ucm/VoiceCall.conf | 145 ++++++++++++++++++
srcpkgs/pinephone-base/template | 13 +-
7 files changed, 361 insertions(+), 3 deletions(-)
create mode 100644 srcpkgs/pinephone-base/files/00-alsa-pinephone-dshare.conf
create mode 100644 srcpkgs/pinephone-base/files/COPYING
create mode 100755 srcpkgs/pinephone-base/files/pinephone-modem-setup
create mode 100644 srcpkgs/pinephone-base/files/ucm/HiFi.conf
create mode 100644 srcpkgs/pinephone-base/files/ucm/PinePhone.conf
create mode 100644 srcpkgs/pinephone-base/files/ucm/VoiceCall.conf
diff --git a/srcpkgs/pinephone-base/files/00-alsa-pinephone-dshare.conf b/srcpkgs/pinephone-base/files/00-alsa-pinephone-dshare.conf
new file mode 100644
index 00000000000..0bb107be419
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/00-alsa-pinephone-dshare.conf
@@ -0,0 +1,14 @@
+pcm_slave.sl2 {
+ pcm "hw:0,0"
+ rate 88200
+}
+
+pcm.!default {
+ type plug
+ slave.pcm {
+ type dshare
+ ipc_key 1023984
+ slave sl2
+ bindings [ 0 1 ]
+ }
+}
diff --git a/srcpkgs/pinephone-base/files/COPYING b/srcpkgs/pinephone-base/files/COPYING
new file mode 100644
index 00000000000..1bf3fc55f9b
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/COPYING
@@ -0,0 +1,15 @@
+The following list of files are copyright of postmarketOS, and are used with
+some modifications under the terms of the MIT license
+https://opensource.org/licenses/MIT
+
+90-modem-eg25.rules
+pinephone-modem-setup
+00-alsa-pinephone-dshare.conf
+ucm/PinePhone.conf
+ucm/HiFi.conf
+ucm/VoiceCall.conf
+
+---
+
+see for sources:
+https://gitlab.com/postmarketOS/pmaports/-/tree/master/device/main/device-pine64-pinephone
\ No newline at end of file
diff --git a/srcpkgs/pinephone-base/files/pinephone-modem-setup b/srcpkgs/pinephone-base/files/pinephone-modem-setup
new file mode 100755
index 00000000000..a734cb17069
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/pinephone-modem-setup
@@ -0,0 +1,26 @@
+#!/bin/sh
+
+DEV=${DEV:-$1}
+
+log() {
+ echo "$@" | logger -t "void:modem-setup"
+}
+
+QMBNCFG_CONFIG="1"
+
+# Read current config
+QMBNCFG_ACTUAL_CONFIG=$(echo 'AT+QMBNCFG="AutoSel"' | atinout - $DEV -)
+
+if echo $QMBNCFG_ACTUAL_CONFIG | grep -q $QMBNCFG_CONFIG
+then
+ log "Modem already configured"
+ exit 0
+fi
+
+# Configure VoLTE auto selecting profile
+RET=$(echo "AT+QMBNCFG=\"AutoSel\",$QMBNCFG_CONFIG" | atinout - $DEV -)
+if ! echo $RET | grep -q OK
+then
+ log "Failed to enable VoLTE profile auto selecting: $RET"
+ exit 1
+fi
diff --git a/srcpkgs/pinephone-base/files/ucm/HiFi.conf b/srcpkgs/pinephone-base/files/ucm/HiFi.conf
new file mode 100644
index 00000000000..e50942ce284
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/ucm/HiFi.conf
@@ -0,0 +1,140 @@
+SectionVerb {
+ EnableSequence [
+ cset "name='Headphone Playback Switch' off"
+ cset "name='Headphone Source Playback Route' DAC"
+ cset "name='Line In Playback Switch' off"
+ cset "name='Line Out Playback Switch' off"
+ cset "name='Line Out Source Playback Route' Mono Differential"
+ cset "name='Mic1 Playback Switch' off"
+ cset "name='Mic2 Playback Switch' off"
+ cset "name='AIF1 DA0 Playback Volume' 160"
+ cset "name='AIF3 ADC Source Capture Route' None"
+ cset "name='AIF2 DAC Source Playback Route' None"
+ cset "name='DAC Playback Switch' on"
+ cset "name='DAC Playback Volume' 160"
+ cset "name='ADC Digital DAC Playback Switch' off"
+ cset "name='AIF1 Slot 0 Digital DAC Playback Switch' on"
+ cset "name='AIF2 Digital DAC Playback Switch' off"
+ cset "name='DAC Reversed Playback Switch' off"
+ cset "name='Earpiece Playback Switch' off"
+ cset "name='Earpiece Source Playback Route' DACL"
+
+ cset "name='Line In Capture Switch' off"
+ cset "name='Mic1 Capture Switch' off"
+ cset "name='Mic1 Boost Volume' 7"
+ cset "name='Mic2 Capture Switch' off"
+ cset "name='Mic2 Boost Volume' 7"
+ cset "name='Mixer Capture Switch' off"
+ cset "name='Mixer Reversed Capture Switch' off"
+ cset "name='ADC Capture Volume' 160"
+ cset "name='ADC Gain Capture Volume' 7"
+ cset "name='AIF1 AD0 Capture Volume' 160"
+ cset "name='AIF1 Data Digital ADC Capture Switch' on"
+ cset "name='AIF2 ADC Mixer ADC Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF2 DAC Rev Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ ]
+
+ DisableSequence [
+ ]
+
+ Value {
+ }
+}
+
+SectionDevice."Speaker" {
+ Comment "Internal speaker"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Mix Mono"
+ cset "name='Line Out Playback Switch' on"
+ cset "name='Line Out Playback Volume' 100%"
+ ]
+
+ DisableSequence [
+ cset "name='Line Out Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Line Out Playback Volume"
+ PlaybackSwitch "Line Out Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 300
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
+SectionDevice."Earpiece" {
+ Comment "Internal Earpiece"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Mix Mono"
+ cset "name='Earpiece Playback Switch' on"
+ cset "name='Earpiece Playback Volume' 100%"
+ ]
+
+ DisableSequence [
+ cset "name='Earpiece Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Earpiece Playback Volume"
+ PlaybackSwitch "Earpiece Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 200
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
+SectionDevice."Mic" {
+ Comment "Internal Microphone"
+ ConflictingDevice [
+ "Headset"
+ ]
+ EnableSequence [
+ cset "name='Mic1 Capture Switch' on"
+ ]
+ DisableSequence [
+ cset "name='Mic1 Capture Switch' off"
+ ]
+ Value {
+ CapturePriority 500
+ CapturePCM "hw:${CardId},0"
+ CaptureChannels 2
+ }
+}
+SectionDevice."Headset" {
+ Comment "Headset Microphone"
+ ConflictingDevice [
+ "Mic"
+ ]
+ EnableSequence [
+ cset "name='Mic2 Capture Switch' on"
+ ]
+ DisableSequence [
+ cset "name='Mic2 Capture Switch' off"
+ ]
+ Value {
+ CapturePriority 100
+ CapturePCM "hw:${CardId},0"
+ CaptureChannels 2
+ }
+}
+SectionDevice."Headphones" {
+ Comment "Headset"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Stereo"
+ cset "name='Headphone Playback Switch' on"
+ cset "name='Headphone Playback Volume' 40%"
+ ]
+
+ DisableSequence [
+ cset "name='Headphone Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Headphone Playback Volume"
+ PlaybackSwitch "Headphone Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 100
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
diff --git a/srcpkgs/pinephone-base/files/ucm/PinePhone.conf b/srcpkgs/pinephone-base/files/ucm/PinePhone.conf
new file mode 100644
index 00000000000..9a8ea12b28a
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/ucm/PinePhone.conf
@@ -0,0 +1,11 @@
+Syntax 2
+
+SectionUseCase."HiFi" {
+ File "HiFi.conf"
+ Comment "Play HiFi quality music"
+}
+
+SectionUseCase."Voice Call" {
+ File "VoiceCall.conf"
+ Comment "Make a phone call"
+}
diff --git a/srcpkgs/pinephone-base/files/ucm/VoiceCall.conf b/srcpkgs/pinephone-base/files/ucm/VoiceCall.conf
new file mode 100644
index 00000000000..dedbcaaabfd
--- /dev/null
+++ b/srcpkgs/pinephone-base/files/ucm/VoiceCall.conf
@@ -0,0 +1,145 @@
+SectionVerb {
+ EnableSequence [
+ cset "name='Headphone Playback Switch' off"
+ cset "name='Headphone Source Playback Route' DAC"
+ cset "name='Line In Playback Switch' off"
+ cset "name='Line Out Playback Switch' off"
+ cset "name='Line Out Source Playback Route' Mono Differential"
+ cset "name='Mic1 Playback Switch' off"
+ cset "name='Mic2 Playback Switch' off"
+ cset "name='AIF1 DA0 Playback Volume' 160"
+ cset "name='AIF2 DAC Playback Volume' 160"
+ cset "name='AIF3 ADC Source Capture Route' None"
+ cset "name='AIF2 DAC Source Playback Route' None"
+ cset "name='DAC Playback Switch' on"
+ cset "name='DAC Playback Volume' 160"
+ cset "name='ADC Digital DAC Playback Switch' off"
+ cset "name='AIF1 Slot 0 Digital DAC Playback Switch' on"
+ cset "name='AIF2 Digital DAC Playback Switch' on"
+ cset "name='DAC Reversed Playback Switch' off"
+ cset "name='Earpiece Playback Switch' off"
+ cset "name='Earpiece Source Playback Route' DACL"
+
+ cset "name='Line In Capture Switch' off"
+ cset "name='Mic1 Capture Switch' off"
+ cset "name='Mic1 Boost Volume' 0"
+ cset "name='Mic1 Playback Volume' 7"
+ cset "name='Mic2 Capture Switch' off"
+ cset "name='Mic2 Boost Volume' 0"
+ cset "name='Mic2 Playback Volume' 7"
+ cset "name='Mixer Capture Switch' off"
+ cset "name='Mixer Reversed Capture Switch' off"
+ cset "name='ADC Capture Volume' 160"
+ cset "name='ADC Gain Capture Volume' 7"
+ cset "name='AIF1 AD0 Capture Volume' 160"
+ cset "name='AIF1 Data Digital ADC Capture Switch' on"
+ cset "name='AIF2 ADC Capture Volume' 160"
+ cset "name='AIF2 ADC Mixer ADC Capture Switch' on"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF2 DAC Rev Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ cset "name='AIF2 ADC Mixer AIF1 DA0 Capture Switch' off"
+ ]
+
+ DisableSequence [
+ ]
+
+ Value {
+ PlaybackRate 8000
+ }
+}
+
+SectionDevice."Speaker" {
+ Comment "Internal speaker"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Mix Mono"
+ cset "name='Line Out Playback Switch' on"
+ cset "name='Line Out Playback Volume' 100%"
+ ]
+
+ DisableSequence [
+ cset "name='Line Out Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Line Out Playback Volume"
+ PlaybackSwitch "Line Out Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 300
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
+SectionDevice."Earpiece" {
+ Comment "Internal Earpiece"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Mix Mono"
+ cset "name='Earpiece Playback Switch' on"
+ cset "name='Earpiece Playback Volume' 100%"
+ ]
+
+ DisableSequence [
+ cset "name='Earpiece Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Earpiece Playback Volume"
+ PlaybackSwitch "Earpiece Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 500
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
+SectionDevice."Mic" {
+ Comment "Internal Microphone"
+ ConflictingDevice [
+ "Headset"
+ ]
+ EnableSequence [
+ cset "name='Mic1 Capture Switch' on"
+ ]
+ DisableSequence [
+ cset "name='Mic1 Capture Switch' off"
+ ]
+ Value {
+ CapturePriority 200
+ CapturePCM "hw:${CardId},0"
+ CaptureChannels 2
+ }
+}
+SectionDevice."Headset" {
+ Comment "Headset Microphone"
+ ConflictingDevice [
+ "Mic"
+ ]
+ EnableSequence [
+ cset "name='Mic2 Capture Switch' on"
+ ]
+ DisableSequence [
+ cset "name='Mic2 Capture Switch' off"
+ ]
+ Value {
+ CapturePriority 100
+ CapturePCM "hw:${CardId},0"
+ CaptureChannels 2
+ }
+}
+SectionDevice."Headphones" {
+ Comment "Headset"
+ EnableSequence [
+ cset "name='AIF1 DA0 Stereo Playback Route' Stereo"
+ cset "name='Headphone Playback Switch' on"
+ cset "name='Headphone Playback Volume' 40%"
+ ]
+
+ DisableSequence [
+ cset "name='Headphone Playback Switch' off"
+ ]
+
+ Value {
+ PlaybackVolume "Headphone Playback Volume"
+ PlaybackSwitch "Headphone Playback Switch"
+ PlaybackChannels 2
+ PlaybackPriority 100
+ PlaybackPCM "hw:${CardId},0"
+ }
+}
diff --git a/srcpkgs/pinephone-base/template b/srcpkgs/pinephone-base/template
index 6c750a92bd5..3b7bdae1498 100644
--- a/srcpkgs/pinephone-base/template
+++ b/srcpkgs/pinephone-base/template
@@ -1,15 +1,22 @@
# Template file for 'pinephone-base'
pkgname=pinephone-base
-version=0.1
+version=0.2
revision=1
archs="aarch64*"
build_style=meta
-depends="pinephone-kernel pinephone-uboot"
+depends="pinephone-kernel pinephone-uboot alsa-ucm-conf"
short_desc="Void Linux PinePhone platform package"
maintainer="John Sullivan <jsullivan@csumb.edu>"
-license="Public Domain"
+license="MIT"
homepage="https://www.voidlinux.org"
do_install() {
vinstall "${FILESDIR}/90-modem-eg25.rules" 644 usr/lib/udev/rules.d
+ vinstall "${FILESDIR}/00-alsa-pinephone-dshare.conf" 644 etc/alsa/conf.d
+ vbin "${FILESDIR}/pinephone-modem-setup"
+
+ vmkdir usr/share/alsa/ucm2
+ vcopy "${FILESDIR}/ucm" usr/share/alsa/ucm2/PinePhone
+
+ vlicense "${FILESDIR}/COPYING"
}
next prev parent reply other threads:[~2021-02-05 10:17 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-25 9:18 [PR PATCH] " jjsullivan5196
2021-01-29 3:10 ` ericonr
2021-01-29 4:08 ` jjsullivan5196
2021-02-05 10:17 ` jjsullivan5196 [this message]
2021-02-05 10:19 ` [PR PATCH] [Updated] " jjsullivan5196
2021-02-05 10:20 ` jjsullivan5196
2021-02-05 10:22 ` jjsullivan5196
2021-02-06 5:00 ` [PR REVIEW] " the-maldridge
2021-02-06 5:13 ` jjsullivan5196
2021-02-06 5:15 ` the-maldridge
2021-02-06 5:19 ` ericonr
2021-02-06 5:32 ` [PR PATCH] [Updated] " jjsullivan5196
2021-02-06 5:35 ` [PR REVIEW] " jjsullivan5196
2021-02-06 7:06 ` [PR PATCH] [Updated] " jjsullivan5196
2021-02-06 7:09 ` jjsullivan5196
2021-02-06 7:15 ` jjsullivan5196
2021-02-06 7:21 ` jjsullivan5196
2021-02-22 21:39 ` MungFuSensei
2021-02-24 4:03 ` [PR REVIEW] " ericonr
2021-02-24 4:03 ` ericonr
2021-02-24 4:03 ` ericonr
2021-02-25 19:38 ` Piraty
2021-03-01 0:14 ` [PR PATCH] [Updated] " jjsullivan5196
2021-03-01 0:15 ` [PR REVIEW] " jjsullivan5196
2021-03-01 0:15 ` jjsullivan5196
2021-03-01 0:17 ` the-maldridge
2021-03-01 0:18 ` [PR REVIEW] " jjsullivan5196
2022-04-09 9:28 ` JamiKettunen
2022-04-18 20:17 ` HadetTheUndying
2022-07-19 2:14 ` github-actions
2022-08-07 2:13 ` [PR PATCH] [Closed]: " github-actions
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210205101739.tV861E6kD_7IyDG-8-7j37E3he_x0iRgt1zxLOBzr9c@z \
--to=jjsullivan5196@users.noreply.github.com \
--cc=ml@inbox.vuxu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).