From: "Mark C. Otto" <Mark_Otto@FWS.Gov>
To: 9fans@cse.psu.edu
Subject: [9fans] Installing Plan9 on a Toshiba Sattellite 4015CDS Laptop
Date: Mon, 29 Jan 2001 11:59:33 -0500 [thread overview]
Message-ID: <3A75A175.BBC627FF@FWS.Gov> (raw)
In-Reply-To: <E148eTE-000JCQ-0Y@anchor-post-34.mail.demon.net>
[-- Attachment #1: Type: text/plain, Size: 1963 bytes --]
I am trying to install plan9 on a Toshiba Sattellite 4015CDS. I had problems
with aux/vga and was left in rc. I suspect that the problem is in with the
CT65555 video chip. I tried adding
0xC0090="TOSHIBA Video BIOS V1.80" # Toshiba 4015CDS
below the
0xC0090="CHIPS 65550 PCI & VL Accelerated VGA BIOS" # NEC Versa 6030X/6200MX
line. The 65550 chip is supported but not the 65555. I got a
aux/vga: hiqvideo: DID 00E5 unsupported
error. The specs for the 65555 are on http://www.asiliant.com/65555.htm. The
Adding a New VGA Controller section, VGADB(6), looks beyond me. Has anyone else
added or looked at adding support for the Toshiba Sattelites, especially ones
with the CT65555 chip?
Mark
The laptop speces are on http://www.support.toshiba.com
Toshiba Sattellite 4015CDS
CPU: Intel Mobil Pentium II 266MHz (1.7v/18.v/3.3v)
Motherboard: Intel 440BX system board
Buses: PCI Bus v.2.1 32bit, 33MHz; ISA Bus 16bit, 8.33MHz
Memory: 32MB RAM
BIOS: (512KB: $MBit Flash EPROMJ, 5V)
Display: Color Bright Dual Scan (800x600), Dot pitch: 0.3075mm by 0.3075mm
Video: CT65555, 2MB DirectDraw, H/W Cursor, BitBLT
Modem 3Com-Noteworthy 56K PC Card Modem
Ethernet: 3Com-Megahertz 10Mbps LAN 3CXE589ET
Mouse: PS/2 mouse with wheel
Sound: Yamaha OPL3-SA3, supports SoundBlaster Pro V3.01
Hard Drive: 4.1GB Enhanced IDE
CD-ROM: 24X, .ATAPI (Enhanced IDE)
Floppy: 1.44MB
Here are the devices found on the boot:
cpu0: 267MHz Genuine Intel Pentium IT/Xeon (cpuid: AX 0x0652 DX 0x183F9FF)
#y0: 2 slot Intel 82365SL: port 0x3E0 irq 5
dev A0 port 1F0 config 0040 capabilities 0F00 mwdma 0007 udma 0407 dma 00550004
rwm 16
dev A0 port 170 config 85C0 capabilities 0F00 mwdma 0407 dma 00000004 rwm 0
4732 free pages
18928K bytes
98928K swap
I attached my plan9.ini and vgainfo.txt. The vgainfo.txt is the one before I
added the line to vgadb, because it looked more informative.
[-- Attachment #2: plan9.ini --]
[-- Type: text/plain, Size: 181 bytes --]
*nomp=1
distname=plan9
partition=new
monitor=multisync75
#vgasize=640x480x8
vgasize=600x800x8
mouseport=ps2
bootargs=local!#f0/fd0disk
bootfile=fd0!dos!9pcflop.gz
debug=1
[-- Attachment #3: vgainfo.txt --]
[-- Type: text/plain, Size: 2516 bytes --]
aux/vga: controller not in /lib/vgadb
0xC0000 55 AA 60 CB 3F 37 34 30 30 30 30 30 30 30 30 30 U.`.?74000000000
0xC0010 30 30 30 30 30 30 30 BA 78 01 30 30 30 30 49 42 0000000.x.0000IB
0xC0020 4D 20 56 47 41 20 43 6F 6D 70 61 74 69 62 6C 65 M VGA Compatible
0xC0030 20 42 49 4F 53 2E 20 34 1A 05 81 00 92 01 A2 01 BIOS. 4........
0xC0040 B0 01 F2 01 E9 7F 97 86 D0 D2 E0 E6 40 C2 DC C8 ............@...
0xC0050 40 A8 CA C6 D0 DC DE D8 DE CE D2 CA E6 58 40 92 @............X@.
0xC0060 DC C6 5C 00 FF 01 55 44 36 16 0A 00 55 44 FD 0A ..\...UD6...UD..
0xC0070 01 00 00 08 1C CE 07 0D 1F 07 0A 00 A0 7F 00 47 ...............G
0xC0080 00 00 C0 00 B0 00 00 47 00 00 00 6D 1B 00 00 00 .......G...m....
0xC0090 54 4F 53 48 49 42 41 20 56 69 64 65 6F 20 42 49 TOSHIBA Video BI
0xC00A0 4F 53 20 56 31 2E 38 30 0D 0A 00 00 00 00 00 00 OS V1.80........
0xC00B0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0xC00C0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0xC00D0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0xC00E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0xC00F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
main->snarf
vga->snarf
vga->dump
vga misc 67
vga feature 01
vga sequencer 03 00 03 00 02
vga crt 5F 4F 50 82 55 81 BF 1F - 00 4F 0D 0E 00 00 07 80
9C 8E 8F 28 1F 96 B9 A3 - FF
vga graphics 00 00 00 00 00 10 0E 00 - FF
vga attribute 00 01 02 03 04 05 14 07 - 38 39 3A 3B 3C 3D 3E 3F
0C 00 0F 08 00
vga apz 0
vga linear 0
vmf 25175000 vmdf 0 vf1 0 vbw 0
vga->init
dbdumpmode
type=vga, size=640x480x1
frequency=25175000
x=640 (0x280), y=480 (0x1E0), z=1 (0x1)
ht=800 (0x320), shb=664 (0x298), ehb=760 (0x2F8)
shs=664 (0x298), ehs=760 (0x2F8)
vt=525 (0x20D), vrs=491 (0x1EB), vre=493 (0x1ED)
hsync=0, vsync=0, interlace=0
vga->dump
vga flag Fdump|Finit|Fsnarf
vga misc E3
vga feature 01
vga sequencer 03 01 0F 00 06
vga crt 5F 4F 52 9F 53 1F20B 3E - 00 40 00 00 00 00 00 00
1EB 2D1DF 28 001EB1EC C3 -7FF
vga graphics 00 00 00 00 00 00 05 0F - FF
vga attribute 00 01 02 03 04 05 06 07 - 08 09 0A 0B 0C 0D 0E 0F
01 FF 0F 00 00
vga apz 0
vga linear 0
main->exits
next prev parent reply other threads:[~2001-01-29 16:59 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-12-20 8:19 [9fans] Communication with a Network Printer nigel
2001-01-29 16:59 ` Mark C. Otto [this message]
2001-03-19 9:43 ` [9fans] Installing Plan9 on a Toshiba Sattellite 4015CDS Laptop Michael Collins
2001-03-22 17:23 ` Mark C. Otto
2001-03-22 18:17 jmk
2001-03-26 8:45 ` Michael Collins
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3A75A175.BBC627FF@FWS.Gov \
--to=mark_otto@fws.gov \
--cc=9fans@cse.psu.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).