Re: [9fans] trouble with iso bootstrap

Re: [9fans] trouble with iso bootstrap

[erik quanstrom]

> try this but nothing happens. Always 'boot from:' prompt reply.
>
> This is what I see at boot time (using 9atom.iso in my travelmate 4650)
>
> PBS1...Plan9 from Bell Labs
> ELCR: 0C20
> pcirouting: South Bridge 8086, 2641 not found
> dev A0 port 170 config 045A capabilities 2B00 mwdma 0007 udma 203F
> aoepnp(<nil>)
> found 6 e820 entries
> bood devices: fd0
> boot from:

the one ide port has been found.  device sdD0.
(secondary port 0x170, primary device A0)
but you are not given the option of booting from sdD0.
a quick drive-by of the code suggests that the error
register has some junk in it.  i would almost bet
this means that the media change bit has been set.

i'll try to get a bootable cd for you to try later today.

- erik

Re: [9fans] trouble with iso bootstrap

[baux80]

On 29 September 2009 at 12:01, erik quanstrom <quanstro@quanstro.net> wrote:
> > dev A0 port 170 config 045A capabilities 2B00 mwdma 0007 udma 203F
> > aoepnp(<nil>)
> > found 6 e820 entries
> > bood devices: fd0
> > boot from:
>
> the one ide port has been found.  device sdD0.
> (secondary port 0x170, primary device A0)
> but you are not given the option of booting from sdD0.
> a quick drive-by of the code suggests that the error
> register has some junk in it.  i would almost bet
> this means that the media change bit has been set.
>
> i'll try to get a bootable cd for you to try later today.

I could try to boot it from qemu and prepare a bootable cd from myself
if you suggest me main steps to do it, or if you could do both this I would
appreciate :)

thank you very much

bye

Re: [9fans] trouble with iso bootstrap

[baux80]

On 29 September 2009 at 6:52, erik quanstrom <quanstro@quanstro.net> wrote:
>
> the drives are on the legacy ports, so
> you want sd[CD][01]!cdboot!9pccd.gz
> i'm sorry i can't tell you which one from
> the kernel output.

try this but nothing happens. Always 'boot from:' prompt reply.

This is what I see at boot time (using 9atom.iso in my travelmate 4650)

PBS1...Plan9 from Bell Labs
ELCR: 0C20
pcirouting: South Bridge 8086, 2641 not found
dev A0 port 170 config 045A capabilities 2B00 mwdma 0007 udm6 203F
eoepnp(<nil>)
found 6 e820 entries
bood devices: fw0
boot from:

if write sdC0!cdboot!9pccd.gz (or C1 or D0 or D1 or anithing [A-F][0-1]) the
reply is 'boot from: ' and no boot nor errors or anithing else.
Should I write something particular to load kernel (tried boot or similar)?

thanks in advance.

bye

Re: [9fans] trouble with iso bootstrap

[erik quanstrom]

00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
05:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
05:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
05:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
05:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
05:04.2 SD Host controller: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01)
05:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
05:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)

1: "

On Tue Sep 29 06:03:12 EDT 2009, baux80@gmail.com wrote:
>
> Hi all,
> 	I'm tring to bootstrap plan9 iso (plan9.iso and 9atom.iso) on my
> laptop but... nothing to do.
>
> At prompt 'boot from:' I've tried some:
>
> sd<X><N>!cdboot!plan9.ini <return>
>
> at return nothing happens and 'boot from:' is here anymore (no errors nor
> warning, nothing but 'boot from:').
>
> I've sdA0 or 1 sdB0 or 1 sdC0 or 1 sdD0 or 1 sdE0 or 1 sdF0 or 1.
>
> Next is my dmesg and lspci (got with a knoppix linux), as main system I've
> OpenBSD.

the drives are on the legacy ports, so
you want sd[CD][01]!cdboot!9pccd.gz
i'm sorry i can't tell you which one from
the kernel output.

- erik

[9fans] trouble with iso bootstrap

[baux80]

Hi all,
	I'm tring to bootstrap plan9 iso (plan9.iso and 9atom.iso) on my
laptop but... nothing to do.

At prompt 'boot from:' I've tried some:

sd<X><N>!cdboot!plan9.ini <return>

at return nothing happens and 'boot from:' is here anymore (no errors nor
warning, nothing but 'boot from:').

I've sdA0 or 1 sdB0 or 1 sdC0 or 1 sdD0 or 1 sdE0 or 1 sdF0 or 1.

Next is my dmesg and lspci (got with a knoppix linux), as main system I've
OpenBSD.

Thank you in advance.

-- dmesg
Linux version 2.6.24.4 (root@Knoppix) (gcc version 4.2.3 (Debian 4.2.3-2)) #2 SMP PREEMPT Tue Mar 25 21:35:28 CET 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003f7df000 (usable)
 BIOS-e820: 000000003f7e0000 - 000000003f7fffc0 (ACPI data)
 BIOS-e820: 000000003f7fffc0 - 000000003f800000 (ACPI NVS)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 260063) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   260063
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   260063
On node 0 totalpages: 260063
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 239 pages used for memmap
  HighMem zone: 30448 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000E5010, 0014 (r0 INSYDE)
ACPI: RSDT 3F7F853B, 0038 (r1 INSYDE RSDT_000      100 ABCD    10200)
ACPI: FACP 3F7FFAC0, 0074 (r1 INSYDE FACP_000      100 0000    10200)
ACPI: DSDT 3F7F8BA0, 6F1C (r1 COMPAL EDL00           1 INTL  2002036)
ACPI: FACS 3F7FFFC0, 0040
ACPI: APIC 3F7FFB50, 0066 (r1 STUPID MAPIC_00 30307830 ABCD    10200)
ACPI: MCFG 3F7FFBC0, 003C (r1 INSYDE MCFG_000 30303030 0000 30303030)
ACPI: SSDT 3F7F874B, 0277 (r1  PmRef  Cpu0Ist     3000 INTL 20030522)
ACPI: SSDT 3F7F8573, 01D8 (r1  PmRef  Cpu0Cst     3001 INTL 20030522)
ACPI: DMI detected: Acer
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
IOAPIC[1]: apic_id 2, version 255, address 0xfec10000, GSI 24-279
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f800000:c0700000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 258032
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 initrd=minirt.gz nomce highres=off loglevel=0 libata.atapi_enabled=1 quiet SELINUX_INIT=NO nmi_watchdog=0 BOOT_IMAGE=knoppix BOOT_IMAGE=linux
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec10000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1995.019 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1023320k/1040252k available (3742k kernel code, 16180k reserved, 1262k data, 420k init, 122748k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe13000 - 0xfffff000   (1968 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc05ea000 - 0xc0653000   ( 420 kB)
      .data : 0xc04a78c8 - 0xc05e327c   (1262 kB)
      .text : 0xc0100000 - 0xc04a78c8   (3742 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3994.32 BogoMIPS (lpj=6654916)
Security Framework initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000180 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) M processor 2.00GHz stepping 08
Total of 1 processors activated (3994.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xea814, last bus=5
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
Force enabled HPET at base address 0xfed00000
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1300-133f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xf0008000-0xf000bfff has been reserved
system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:01: iomem range 0xfec10000-0xfec10fff has been reserved
system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:05: ioport range 0x600-0x60f has been reserved
system 00:05: ioport range 0x680-0x6ff has been reserved
system 00:05: ioport range 0x800-0x80f has been reserved
system 00:05: ioport range 0x1000-0x107f has been reserved
system 00:05: ioport range 0x1180-0x11bf has been reserved
system 00:05: ioport range 0x1640-0x164f has been reserved
system 00:05: ioport range 0xff2c-0xff2f has been reserved
system 00:05: iomem range 0xe0000000-0xefffffff has been reserved
system 00:05: iomem range 0xf0008000-0xf000bfff has been reserved
system 00:05: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:05: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:05: iomem range 0xfed19000-0xfed19fff has been reserved
PCI: Bridge: 0000:00:1c.0
  IO window: c000-dfff
  MEM window: c8000000-cfffffff
  PREFETCH window: 98000000-9fffffff
PCI: Bridge: 0000:00:1c.1
  IO window: a000-bfff
  MEM window: c4000000-c7ffffff
  PREFETCH window: 94000000-97ffffff
PCI: Bus 6, cardbus bridge: 0000:05:04.0
  IO window: 00008000-000080ff
  IO window: 00008400-000084ff
  PREFETCH window: 8c000000-8fffffff
  MEM window: c0000000-c3ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 8000-9fff
  MEM window: bc000000-c3ffffff
  PREFETCH window: 8c000000-93ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ 17
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1441k freed
audit: initializing netlink socket (disabled)
audit(1254216245.499:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.9)
SELinux:  Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
ALI M7101 PMU not found.
vesafb: framebuffer at 0xa0000000, mapped to 0xf8880000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Linux agpgart interface v0.102
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xa0000000
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
intelfb: Cannot reserve FB region.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hdb: TSSTcorpCD/DVDW TS-L632B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
hdd: IRQ probe failed (0xfffffcfe)
hdd: IRQ probe failed (0xfffffcfe)
hdc: FUJITSU MHW2080AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63
hdc: cache flushes supported
 hdc: hdc1
 hdc1: <openbsd: hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 hdc11 hdc12 hdc13 >
hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v2.0-724.
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ahci: probe of 0000:00:1f.2 failed with error -22
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.2
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:1f.2
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.2
pata_acpi 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:1f.2
pata_acpi 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
pata_acpi 0000:00:1f.2: no available native port
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0x40000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00001200
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 18, io base 0x00001220
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 20, io base 0x00001240
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 17, io base 0x00001260
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
drivers/usb/host/r8a66597-hcd.c: driver r8a66597_hcd, 29 May 2007
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad as /class/input/input2
EDAC MC: Ver: 2.1.0 Mar 25 2008
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
cpuidle: using governor ladder
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
ALSA device list:
  No soundcards found.
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI No-Shortcut mode
Freeing unused kernel memory: 420k freed
Failed initialization of WD-7000 SCSI card!
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[bc020000-bc0207ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f5971406dd3]
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.624
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 60323 blocks, 131072 bytes/block, largest block is 131118 bytes.
cloop: loaded 128 blocks into cache.
ISO 9660 Extensions: RRIP_1991A
cloop: losetup_file: 27172 blocks, 131072 bytes/block, largest block is 131118 bytes.
cloop: loaded 128 blocks into cache.
ISO 9660 Extensions: RRIP_1991A
aufs 20080324
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
ACPI: ACPI Dock Station Driver
ACPI: \_SB_.PCI0.SATA.PRID.P_D1: found ejectable bay
ACPI: \_SB_.PCI0.SATA.PRID.P_D1: Adding notify handler
ACPI: Bay [\_SB_.PCI0.SATA.PRID.P_D1] Added
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
input: Video Bus as /class/input/input7
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
input: Video Bus as /class/input/input8
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
Clocksource tsc unstable (delta = -105502399 ns)
Time: hpet clocksource has been installed.
cpufreq: No nForce2 chipset.
powernow: This module only works with AMD K7 CPUs
Marking TSC unstable due to: cpufreq changes.
Yenta: CardBus bridge found at 0000:05:04.0 [1025:007a]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:05:04.0, mfunc 0x89500212, devctl 0x44
Yenta: ISA IRQ mask 0x0000, PCI irq 17
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#05) from #05 to #09
pcmcia: parent PCI bridge I/O window: 0x8000 - 0x9fff
cs: IO port probe 0x8000-0x9fff: clean.
pcmcia: parent PCI bridge Memory window: 0xbc000000 - 0xc3ffffff
pcmcia: parent PCI bridge Memory window: 0x8c000000 - 0x93ffffff
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 21
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1e.2 to 64
ieee80211_crypt: registered algorithm 'NULL'
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
intel8x0_measure_ac97_clock: measured 52544 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1e.3 to 64
tg3.c:v3.86 (November 9, 2007)
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 21 (level, low) -> IRQ 22
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:0f:b0:94:3f:16
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
sdhci: SDHCI controller found at 0000:05:04.2 [1524:0550] (rev 1)
ACPI: PCI Interrupt 0000:05:04.2[B] -> GSI 17 (level, low) -> IRQ 16
mmc0: SDHCI at 0xbc000100 irq 16 PIO
sdhci: SDHCI controller found at 0000:05:04.4 [1524:0551] (rev 1)
PCI: Enabling device 0000:05:04.4 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:04.4[B] -> GSI 17 (level, low) -> IRQ 16
mmc1: SDHCI at 0xbc000300 irq 16 PIO
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 22 (level, low) -> IRQ 23
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
warning: process `hwsetup' used the deprecated sysctl system call with 1.23.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: hwsetup.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
[drm] Initialized drm 1.1.0 20060810
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
PCI: Setting latency timer of device 0000:00:02.0 to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
eth0: no IPv6 routers present


-- lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)
00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
05:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
05:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
05:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
05:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
05:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
05:04.2 SD Host controller: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01)
05:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
05:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)